How do I connect to my HC-06 Bluetooth module?

How do I connect to my HC-06 Bluetooth module?

Once the module is configured as you wish, you can pair the module HC-06 to the device of your choice like any Bluetooth device. Select the name of your module in the list of available Bluetooth device (default is HC-06) and enter the PIN code (default is 1234). When it is done, The LED should stop blinking.

How do you set up a Bluetooth module?

Configure Bluetooth Module HC-05 with AT Mode

  1. Introduction: A widely available bluetooth module HC-05 has capability to enable your project with bluetooth.
  2. Building Circuit. Before making the connection make sure to unplug the power source from Arduino UNO.
  3. Configure with AT Mode:
  4. Programming:
  5. Changing Codes:

How many pins does a Bluetooth module have?

Bluetooth serial modules allow all serial enabled devices to communicate with each other using Bluetooth. It has 6 pins, 1.

What is the difference between HC 05 and HC-06?

The HC-05 can be a master or slave. The HC-06 is a slave only. This means the HC-05 can initiate a connection to another device and the HC-06 can only accept a connection from another device.

How do I connect my HC 05 to my computer?

Select the HC-05 Bluetooth Module on the display and double click the Serial Port Icon to connect. Key in default passwords: 1234 on [Passkey] to connect HC-05 Bluetooth Module. After key in correct passkey, the window will show which serial COM is connected to HC-05 Bluetooth Module.

How many pins HC 05 Bluetooth module can remain unconnected?

HC05 PIN DESCRIPTION The HC-05 Bluetooth Module has 6 pins commonly used.

How does the hc-06 Bluetooth module work?

At least on my module the pin was always low, regardless if paired or not. On the HC-05 module, I send “AT ” to the device, and then it responds with “OK ”. But on the HC-06, the protocol is different I need to send “AT” (without the new-line characters), and I receive “OK” (without the new-line characters).

How to connect Bluetooth serial port ( com13 ) on hc-06?

Right-click on the “HC-06” icon and select “Search Services”. One service should be found. Right-click on the “HC-06” icon again and a new option should be listed, writing “Connect Bluetooth Serial Port (COM13)”. Go ahead and select it. Once the link is complete the red flashing light on the HC-06 module should stop blinking and stay red.

What is the PIN code for Arduino module hc-06?

Once the module is configured as you wish, you can pair the module HC-06 to the device of your choice like any Bluetooth device. Select the name of your module in the list of available Bluetooth device (default is HC-06) and enter the PIN code (default is 1234).

How to connect hc06 Bluetooth to serial wireless UART?

Select the HC-06 option and then wait a moment. The LED on the Bluetooth module should stay on and the app will show “connected: HC-06” . Now send the number 1 through the terminal and the onboard LED on the Arduino should turn on. Send 2 and it should turn off.

How does Bluetooth module HC-06 work?

The HC-06 is a class 2 slave Bluetooth module designed for transparent wireless serial communication. Once it is paired to a master Bluetooth device such as PC, smart phones and tablet, its operation becomes transparent to the user. All data received through the serial input is immediately transmitted over the air.

How do I connect my Bluetooth module to my laptop?

What is the difference between HC-05 and HC-06?

What is the range of Bluetooth module HC-06?

to 9 meters
Like the HC-05, the HC-06 module can reach a range of up to 9 meters (30 ft). If you need a Bluetooth module to talk to your smartphone and an Arduino board, the HC-06 would work fine.

How do I put my HC-06 in mode?

For HC06: On arduino serial monitor type “AT” (without the quotes) and press enter, “OK” will confirm AT mode.

Can HC-05 send data?

Mobile app Connecting the Android device to the HC-05 creates a serial communication channel very similar to the serial monitor in the Arduino IDE. This means we need a Bluetooth version of the serial monitor. for doing this go to Settings->Bluetooth->Scan device->select HC-05 and pair it. Pass code to pair is ‘1234’.